Maxtech xpvs336i Manuel d'utilisateur

Part #MAN081 Rev. 1.0 SF-1133HV/R12-PnPHigh PerformanceV.34+/V.42bis33,600 BPS InternalPlug and PlayFAX/Voice/DataModemFeaturing Advanced Full-Duplex

8@ wait for five seconds of silence! flash; return to Command Mode after dialingDS=n Dial one of the four telephone numbers(n=0-3) stored in the modem

9W 1 Report line speed, error correction protocol,and DTE speed.W2 Report DCE speed onlyX_ X0 Hayes Smartmodem 300 compatibleresponses/blind dialing.X

10&P2 Same as &P0 setting but at 20 pulses perminute&P3 Same as &P1 setting but at 20 pulses perminute&R_ &R0 Reserved&R1

11300, 33600. Parameter “a” specifies themodulation protocol desired where: 0=V.21,1=V.22, 2=V.22bis, 3=V.23, 9=V.32,10=V.32bis, 11=V.34, 64=Bell 103,

12\N3 V.42/MNP/Normal data link\N4 V.42 data link only\N5 MNP data link only3.6 Fax Class 1 Commands+FAE=n Data/Fax Auto Answer+FCLASS=n Service Class

13+FPTS= Page Transfer Status+FREV? Identify Revision+FSPL Enable polling+FTSI: Report the Transmit Station ID3.8 Voice Commands#BDR Select Baud Rate#

14Table 4-1 S - RegistersRegister Function Range/units DefaultS0 Auto-answer Ring 0-255 /rings 0S1 Ring counter 0-255 /rings 0S2 Escape code character

15S49-81 ReservedS82 Break options 3, 7, or 128 128S83-85 ReservedS86 Connection failure code 0, 4, 5, 9, 12, 13, 14 *S87-S90ReservedS91 Transmit atte

16data to it. Similarly, IRQ settings must be set correctly toreceive data from the modem.2. Make sure that your modem is initialized correctly. Yourm

17and XON/XOFF software flow control is disabled in thecommunication software.3. Make sure the data speed is not faster than yourcomputer's capab

ContentsSection One Introduction... 1Section Two Installation... 1Section Three AT Command Set ...

18Power: 0.75 WTemperature: 0 to 55 degrees C (Operating)Caller ID: YesPnP: Revision 1.0aSpeakerphone: Full-duplex with DSP echocancellationAppendix B

19cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on,the user is encouraged to tr

20to a telephone loop which is used by the device, to preventoverloading. The termination on a loop may consist of anycombination of devices subject o

21

1Section One - IntroductionThis 33.6 Kbps Plug and Play FAX/Voice/DataSpeakerphone Modem connects your computer to allpopular high speed modems availa

2or,2. If running DOS or Windows 3.x, configure themodem using the included modem driver. Instructionsfor installing this driver are included in the t

36. Replace the computer cover and plug in your com-puter.7. Connect the telephone cable from the modem's LINEconnector to the telephone wall jac

4The Install From Disk dialog box now instructsyou to “Insert the manufacturer's installation disk into thedrive selected, and then click OK.” In

5MANAGER|MAIN|CONTROL PANEL, click on PORTSand follow Windows 3.1x user's manual instructions onconfiguring the installed modem COM port.Proceed

62.7 Testing Your Modem After InstallationIn order to test your modem you should be familiarwith your communication software. Load and set up yourcomm

7Section Three - AT Command Set3.1 Executing CommandsCommands are accepted by the modem while it isin Command Mode. Your modem is automatically inComm